@article { ISI:000330812400022, title = {Single-pot formation of THFAL via catalytic hydrogenation of FFR over Pd/MFI catalyst}, journal = {ACS Sustainable Chemistry \& Engineering}, volume = {2}, number = {2}, year = {2014}, month = {FEB}, pages = {272-281}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

Furfural (FFR) was selectively hydrogenated in a single pot to tetrahydrofurfuryl alcohol (THFAL) over a Si MFI molecular sieve supported Pd catalyst. Studies on catalyst screening revealed that both the metal function and the support were critical for directing the selectivity to the ringhydrogenated product, THFAL. The structural feature of MFI as shown by XRD was completely retained in the used sample of the 3\% Pd/MFI catalyst confirming its stability under reaction conditions. XRD, along with SEM characterization of the used samples, established retention of morphology of the structured silicate, suggesting a strong interaction between hexagonal porous silicate and Pd particles. The complete conversion of FFR with an enhanced selectivity of 95\% to THFAL could be achieved by recycling the crude of the first hydrogenation experiment over the same 3\% Pd/MFI catalyst.

}, keywords = {Biomass conversion, Hydrogenation, Pd/MFI, Recyclability, THFAL}, issn = {2168-0485}, doi = {10.1021/sc400302b}, author = {Biradar, Narayan S. and Hengne, Amol M. and Birajdar, Shobha N. and Niphadkar, Prashant S. and Joshi, Praphulla N. and Rode, Chandrashekhar V.} } @article {47163, title = {Three-dimensional printing with waste high-density polyethylene}, journal = {ACS Applied Polymer Materials}, volume = {1}, year = {2019}, month = {NOV}, pages = {3157-3164}, type = {Article}, abstract = {

Fused filament fabrication (FFF) three-dimensional (3D) printing of semicrystalline polymers such as high density polyethylene (HDPE) is challenging because crystallization-induced shrinkage of the filament, as it cools, results in stresses that warp the printed part and debond it from the print substrate. Here, we demonstrate that waste-derived HDPE can be successfully 3D printed by (i) blending with a small fraction (\<0.5\% by weight) of dimethyl dibenzylidene sorbitol (DMDBS) and (similar to 10\%) linear low density polyethylene (LLDPE) and (ii) printing the object with a thin {\textquoteleft}{\textquoteleft}brim{\textquoteright}{\textquoteright} around it that is adhered to the print substrate using common polyvinyl acetate-based glue. We match our experimental results with FEM simulations that provide insight into the origin of the stresses developed during printing. Because HDPE forms a significant fraction of the plastic waste stream, conversion of waste-derived HDPE to 3D printing filament has important technological implications.

}, keywords = {3d printing polyethylene printing, polymer blend, Recyclability, warpage}, issn = {2637-6105}, doi = {10.1021/acsapm.9b00813}, author = {Gudadhe, Aniket and Bachhar, Nirmalya and Kumar, Anil and Andrade, Prem and Kumaraswamy, Guruswamy} } @article {48782, title = {Recyclable Pd nanoparticles immobilized on amine functionalized LDH for the Suzuki-Miyaura cross-coupling reaction}, journal = {Chemical Papers}, volume = {77}, year = {2023}, month = {SEP}, pages = {5555-5569}, type = {Article}, abstract = {

In the present work, we invented a Pd nanoparticle immobilized on an amine-functionalized LDH catalyst (PdNP@NH2LDH-Al-MCM-41) for cross-coupling reactions. The palladium was grafted onto the support by treating the Pd(OAc)(2) with NH2-LDH-Al-MCM-41 in acetone at room temperature. The prepared catalyst was characterized by FT-IR, SEM, TGA, TEM, and XPS techniques. The TEM characterization of the catalyst showed the uniform distribution of PdNPs with sizes ranging from 3 to 6 nm located inside the mesoporous. The Suzuki-Miyaura cross-coupling reaction was used to demonstrate the catalytic efficiency of the prepared PdNPs@NH2-LDH-Al-MCM-41 catalyst. The prepared and analyzed catalyst showed good to excellent activity in the Suzuki-Miyaura cross-coupling reaction of various aryl bromides with different aryl boronic acids in ethanol at 80 degrees C. The catalyst showed TON up to similar to 47 and TOF similar to 47 h(-1). The catalytic results exhibited that the catalyst is completely recoverable with simple filtration. The catalytic efficiency shows a slight decrease in activity for the Suzuki-Miyaura cross-coupling reactions even after five repeated recycles. TEM images of the freshly prepared and reused catalysts (after five catalytic cycles) showed palladium nanoparticles remain unchanged at the end of the reactions. [GRAPHICS] .

}, keywords = {LDH, PdNPs, Recyclability, Suzuki-Miyaura coupling}, issn = {0366-6352}, doi = {10.1007/s11696-023-02885-2}, author = {Patil, Seema P. P. and Jadhav, Sanjay N. N. and Inamdar, Firoz A. A. and Ameen, Mohd Aatif and Rode, Chandrashekhar V. V. and Rajmane, Archana S. S. and Kumbhar, Arjun S. S.} }